Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Here in the next paragraph you'll find some excellent content about How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult task. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also set in the new one. Ensure you have actually certified on your own for the task and fit attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is better to take into consideration utilizing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This article will certainly assist you set up a brand-new tub in your shower room if you have currently acquired a new tub and also don't require to alter the arrangement of your previous water pipelines.
Your tools as well as material list should consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite troublesome as a result of the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making sure that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, position the tub in the called for placement. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the tub up until the spirit level reads degree.
To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub should wait till the tub has been used at the very least when as this will resolve it right into its final placement.
Getting ready for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to stop strain on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about issues with dampness as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that piece of writing on How to Install a Bathtub when doing a search on the search engines. So long as you appreciated our post please do not forget to share it. Thank you so much for taking the time to read it.
Protect your home, dial! Report this page